espyの日記： obs266 128MB (2)

直前の bootpdがコケていたのは、
サーバ側で /etc/hosts に自アドレスに関する1行を加えることで通るようになった。
IRCでヒントを下さったumqさま、ありがとうございました。
動かなかった状態の時は、コマンドラインで bootpdを直接実行すると、「Can not get my IP address」と
メッセージが出ていた。自分のIPは別サーバーのDHCPで取得済みなんだけれどなぁ．．．と、試しに固定IPに
してみても結果は同じ。これで悩んでしまった。
どうやら、bootpdがちゃんと動く為には、「サーバー側のアドレスが決まっている」という
だけでは駄目みたいで、gethostbyname()でアドレスが得られないと駄目なんだそうな。

三連休の前半部はこれだけ。
そして先へ進み．．．(以下はOpenBlocks側のコンソール)

--- Device Configuration ---
  Power-On Test Devices:
   000  Enabled   System Memory [RAM]
   002  Enabled   Ethernet      [ENET]
   003  Enabled   PCI Ethernet  [PCIENET]
  ----------------------------
  Boot Sources:
   001  Disabled  System FLASH  [FLASH]
   002  Enabled   Ethernet      [ENET]
                  LOCAL:  192.168.2.12
                  REMOTE: 192.168.2.32
                  MAC:    000A8501B910
   004  Enabled   Serial Port 1 [S1]
  ----------------------------
  Debugger: Disabled
  ----------------------------
  1 - Enable/disable tests
  2 - Enable/disable boot devices
  3 - Change IP addresses
  4 - Ping test
  5 - Toggle ROM monitor debugger
  6 - Toggle automatic menu
  7 - Display configuration
  8 - Save changes to configuration
  9 - Set baud rate for s1 boot
  A - Enable/disable I cache (Enabled )
  B - Enable/disable D cache (Enabled )
  F - FLASH image update
  M - Memory Test
  0 - Exit menu and continue
->0
Booting from [ENET] Ethernet     ...
Sending bootp request ...
Loading file "/netbsd.img" ...
Sending tftp boot request ...
Transfer Complete ...
Loaded successfully ...
Entry point at 0x25000 ...
+8000000,
00025000-08000000 -> 00378000-08000000 = 7c88000
Board config data:
  usr_config_ver = 1.4
  rom_sw_ver = 1.2
  mem_size = 134217728
  mac_address_local = 00:0a:85:01:b9:10
  mac_address_pci = 00:0a:85:01:39:10
  processor_speed = 266666666
  plb_speed = 133333333
  pci_speed = 33333333
Loaded initial symtab at 0x2df740, strtab at 0x302a68, # entries 8927
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.
 
NetBSD 3.1 (OPENBLOCKS266) #0: Tue Oct 31 01:49:24 UTC 2006
        [e-mail]:/home/builds/ab/netbsd-3-1-RELEASE/evbppc/200610302
053Z-obj/home/builds/ab/netbsd-3-1-RELEASE/src/sys/arch/evbppc/compile/OPENBLOCK
S266
Model: OpenBlockS266 IBM PowerPC 405GPr Board
total memory = 128 MB
avail memory = 123 MB
plb0 (root)
cpu0 at plb0: 266MHz 405GPr (Revision 9.81)
Instruction cache size 16384 line size 32
Data cache size 16384 line size 32
PVR: owner 509 core family 1 cache 2 version 5 asic 11
ecc0 at plb0 irq 16: ECC controller
opb0 at plb0
com0 at opb0 addr 0xef600300 irq 0: ns16550a, working fifo
com0: console
com1 at opb0 addr 0xef600400 irq 1: ns16550a, working fifo
emac0 at opb0 addr 0xef600800 irq 9: 405GP EMAC
emac0: interrupting at irqs 9 .. 15
emac0: Ethernet address 00:0a:85:01:b9:10
lxtphy0 at emac0 phy 0: LXT971/2 10/100 media interface, rev. 2
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gpio0 at opb0 addr 0xef600700: On-Chip GPIO controller
obsled0 at gpio0 addr GPIO#12: OpenBlockS led1
obsled1 at gpio0 addr GPIO#13: OpenBlockS led2
obsled2 at gpio0 addr GPIO#14: OpenBlockS led4
gpiic0 at opb0 addr 0xef600500 irq 2: On-Chip IIC controller
iic0 at gpiic0: I2C bus
xrtc0 at iic0 addr 0x6f: Xicor X1226 Real-time Clock/NVRAM
wdog0 at opb0: 4 second period
pchb0 at plb0
pchb0: IBM PPC 405GP PCI Bridge (rev. 0x21)
pci0 at pchb0
pci0: i/o space, memory space enabled
IBM PPC 405GP PCI Bridge (host bridge, revision 0x21) at pci0 dev 0 function 0 n
ot configured
hptide0 at pci0 dev 3 function 0
hptide0: Triones/Highpoint HPT371 IDE Controller
hptide0: bus-master DMA support present
hptide0: primary channel wired to native-PCI mode
hptide0: using irq 30 for native-PCI interrupt
atabus0 at hptide0 channel 0
hptide0: secondary channel wired to native-PCI mode
atabus1 at hptide0 channel 1
tlp0 at pci0 dev 4 function 0: Davicom DM9102A Ethernet, pass 4.0
tlp0: broken MicroWire interface detected; setting SROM size to 1Kb
tlp0: interrupting at irq 31
tlp0: Ethernet address 00:0a:85:01:39:10
dmphy0 at tlp0 phy 1: DM9102 10/100 media interface, rev. 1
dmphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pbus at plb0 not configured
biomask 1c02 netmask 1c03 ttymask 1c03
Setting PIT to 266666666/100 = 2666666
root device: emac0
dump device:
file system (default generic): nfs
root on emac0
nfs_boot: trying DHCP/BOOTP
nfs_boot: BOOTP next-server: 192.168.2.32
nfs_boot: my_name=obs266
nfs_boot: my_addr=192.168.2.12
nfs_boot: my_mask=255.255.255.0
root on espilab-vmnb2:/home/export/client/root
root time: 0x463643bd
init path (default /sbin/init):
init: copying out path `/sbin/init' 11
Mon Apr 30 19:10:46 UTC 2007
Checking for botched superblock upgrades: done.
Starting file system checks:
mount_nfs: rpcbind to nfs on server: RPC: Port mapper failure - RPC: Timed out
mount_nfs: rpcbind to nfs on server: RPC: Port mapper failure - RPC: Timed out
mount_nfs: rpcbind to nfs on server: RPC: Port mapper failure - RPC: Timed out
mount_nfs: rpcbind to nfs on server: RPC: Port mapper failure - RPC: Timed out
mount_nfs: rpcbind to nfs on server: RPC: Port mapper failure - RPC: Unable to s
end
mount_nfs: rpcbind to nfs on server: RPC: Port mapper failure - RPC: Timed out
mount_nfs: rpcbind to nfs on server: RPC: Port mapper failure - RPC: Timed out
mount_nfs: rpcbind to nfs on server: RPC: Port mapper failure - RPC: Timed out
mount_nfs: rpcbind to nfs on server: RPC: Port mapper failure - RPC: Timed out
mount_nfs: rpcbind to nfs on server: RPC: Port mapper failure - RPC: Timed out

今度はnfsがうまく動けていない様子。
ディスクレスブートが目的じゃなくて、最終的にはHDDにインストールしたいだけなんだけどな…。
連休の後半部で悩むことにする。ぅぅ。