merlinの日記: S30顛末記
なんとか うごくようになったが サスペンドができない。
APM まわりを いじらなきゃ ならないが 面倒そうである。
後 モデムはLucent/Intel AMR モデムなので
ltmodem が 対応していないことが 判明。
当分 待ちのようである。
無線LANは、3つめのPCMCIAデバイスとして動作しているので
/etc/rc.d/init.d/pcmcia の {start}セクションに
cardctl eject 2 を ほうり込んで、起動時には 動かなくした。
cardctl insert 2 が 実行される スクリプトを作って コマンド
ラインから 起動できるようにした。 これは 便利。
(1 ~11 ch しかつかえないのは 困ったものだが。)
CFスロットは 2つめのPCMCIAデバイスとして動作している。
現在は 2.4.8 にして 動作をみている。
音はALSA ドライバ を現在リビルド中。2.2.18 では これで動いたので問題ないはず。
とりあえす dmesg , /proc/ を ここに 置いて置こう
Linux version 2.4.8 (root@ganimede) (gcc version egcs-2.91.66 19990314/Linux (eg
cs-1.1.2 release)) #3 2001年 9月 6日(木) 05時07分16秒 JST
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3c00 (ACPI data)
BIOS-e820: 000000000fff3c00 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
On node 0 totalpages: 65280
zone(0): 4096 pages.
zone(1): 61184 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux ro root=307 BOOT_FILE=/boot/vmlinuz m
em=255M apm=on
Initializing CPU#0
Detected 298.707 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 596.37 BogoMIPS
Memory: 254132k/261120k available (1264k kernel code, 6600k reserved, 500k data,
236k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfd9cf, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/7198] at 00:07.0
PCI: Found IRQ 11 for device 00:0a.1
PCI: Sharing IRQ 11 with 00:09.0
IRQ routing conflict for 00:0a.0, have irq 5, want irq 11
PCI: Found IRQ 10 for device 00:0c.0
PCI: Sharing IRQ 10 with 00:07.2
got res[10000000:10000fff] for resource 0 of Texas Instruments PCI1420
got res[10001000:10001fff] for resource 0 of Texas Instruments PCI1420 (#2)
got res[10002000:10002fff] for resource 0 of Texas Instruments PCI1410 PC card
Cardbus Controller
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
Starting kswapd v1.8
VFS: Diskquotas version dquot_6.4.0 initialized
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SER
IAL_PCI ISAPNP enabled
PCI: Found IRQ 5 for device 00:00.2
PCI: Sharing IRQ 5 with 00:00.1
Real Time Clock Driver v1.10d
block: 128 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 0
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x18e0-0x18e7, BIOS settings: hda:DMA, hdb:pio
hda: IBM-DJSA-220, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 39070080 sectors (20004 MB) w/1874KiB Cache, CHS=2432/255/63, UDMA(33)
Partition check:
hda: hda1 hda2 hda3
floppy0: no floppy controllers found
task queue still active
atp.c:v1.09 8/9/2000 Donald Becker
http://www.scyld.com/network/atp.html
SCSI subsystem driver Revision: 1.00
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 00:0a.0
PCI: Sharing IRQ 11 with 00:09.0
IRQ routing conflict for 00:0a.0, have irq 5, want irq 11
PCI: Sharing IRQ 11 with 00:0a.1
PCI: Found IRQ 11 for device 00:0a.1
PCI: Sharing IRQ 11 with 00:09.0
IRQ routing conflict for 00:0a.0, have irq 5, want irq 11
PCI: Enabling device 00:0c.0 (0000 -> 0002)
PCI: Found IRQ 10 for device 00:0c.0
PCI: Sharing IRQ 10 with 00:07.2
Intel PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Yenta IRQ list 02d8, PCI irq5
Socket status: 30000006
Yenta IRQ list 02d8, PCI irq11
Socket status: 30000006
Yenta IRQ list 0000, PCI irq10
Socket status: 30000011
usbserial.c: USB Serial support registered for Generic
usb.c: registered new driver serial
usbserial.c: USB Serial Driver core v1.3
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 236k freed
usb-uhci.c: $Revision: 1.259 $ time 04:23:40 Sep 6 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 10 for device 00:07.2
PCI: Sharing IRQ 10 with 00:0c.0
usb-uhci.c: USB UHCI at I/O 0x18c0, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF cfb5c1e0, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: 18c0
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface cfb5c1e0
usb.c: kusbd: /sbin/hotplug add 1
usb.c: kusbd policy returned 0xfffffffe
usb-uhci.c: v1.251:USB Universal Host Controller Interface driver
Adding Swap: 257000k swap-space (priority -1)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
hermes.c: 12 Dec 2000 David Gibson
orinoco.c 0.06c (David Gibson and others)
dldwd: David's Less Dodgy WaveLAN/IEEE Driver
orinoco_cs.c 0.06 (David Gibson and others)
eth0: Firmware ID 1F vendor 0x1 (Lucent) version 6.14
eth0: Ad-hoc demo mode supported.
eth0: IEEE standard IBSS ad-hoc mode supported.
eth0: WEP supported, "128"-bit key.
eth0: MAC address 00:02:2D:14:EE:60
eth0: Station name "HERMES I"
eth0: ready
eth0: index 0x01: Vcc 3.3, irq 10, io 0x0100-0x013f
/proc/devices
Character devices:
1 mem
2 pty
3 ttyp
4 ttyS
5 cua
7 vcs
10 misc
14 sound
29 fb
36 netlink
128 ptm
136 pts
162 raw
180 usb
188 usb/tts/%d
254 pcmcia
Block devices:
1 ramdisk
3 ide0
/proc/interrupts
CPU0
0: 2019878 XT-PIC timer
1: 7511 XT-PIC keyboard
2: 0 XT-PIC cascade
5: 0 XT-PIC Texas Instruments PCI1420
8: 1 XT-PIC rtc
10: 35237 XT-PIC Texas Instruments PCI1410 PC card Cardbus Contr
oller, usb-uhci, orinoco_cs
11: 0 XT-PIC Texas Instruments PCI1420 (#2)
12: 41477 XT-PIC PS/2 Mouse
14: 14726 XT-PIC ide0
NMI: 0
ERR: 0
/proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 10
cpu MHz : 298.707
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat p
se36 mmx fxsr sse
bogomips : 596.37
あれっ? MHZ がぁ?
/proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0100-013f : orinoco_cs
01f0-01f7 : ide0
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1000-10ff : Intel Corporation 82440MX AC'97 Audio Controller
1400-14ff : PCI device 8086:7196 (Intel Corporation)
1800-187f : PCI device 8086:7196 (Intel Corporation)
1880-18bf : Intel Corporation 82440MX AC'97 Audio Controller
18c0-18df : Intel Corporation 82440MX USB Universal Host Controller
18c0-18df : usb-uhci
18e0-18ef : Intel Corporation 82440MX EIDE Controller
18e0-18e7 : ide0
1c00-1cff : PCI CardBus #01
2000-20ff : PCI CardBus #01
2400-24ff : PCI CardBus #05
2800-28ff : PCI CardBus #05
2c00-2cff : PCI CardBus #09
3000-30ff : PCI CardBus #09