Q. If an HDMI accessory device (i.e. switch box, cable booster) does not have a dedicated power supply, is it still compliant and will it work?
An HDMI device that has active electronics should have a provision for external power in order to be compliant (e.g. a receptacle to allow the use of a standard power adapter, sometimes called a power “brick”). Here we are drawing a distinction between “active” devices that actually have some powered electronics, and “passive” devices, such as some switches (more on those later).
Some active devices, such as actively powered HDMI cables or in-line signal extender boxes, will by default attempt to power their electronics by taking power from the 5V line (+5V power) available on the HDMI connector. The HDMI specification requires all source devices to provide at least 55mA (milliamps) on the 5V line for the purpose of reading the EDID of a display. While 55mA is not enough current to operate most HDMI accessory devices (which typically require about 100 to 150mA), most source devices on the market today provide significantly more current on the 5V line than the HDMI specification requires. As a result, the vast majority of accessory devices can operate when interfaced with a source device that provides more than the required current (i.e. over 100-150mA) on the 5V line. However, manufacturers should provide a provision for their powered HDMI accessory devices to obtain external power, and consumers are encouraged to look for this external power provision when purchasing such products.
Looking to the future, not all HDMI devices may provide this much power over the 5V line. For example, as HDMI expands into more and more portable applications (cameras, camcorders, laptops, etc.), power consumption is often much more of an issue, and such devices may not power the 5V line with the > 100mA required by such “active” devices. Again, consumers should consider ensuring that their active HDMI accessory device purchases have a provision for external power for this reason.
The HDMI specification requires all source devices to provide at least 55mA (milliamps) on the 5V line for the purpose of reading the EDID of a display.
そろそろHDMIから電力供給されないかなぁ (スコア:1)
スティック型の魅力がソレで半減してんだよなー
Re: (スコア:0)
http://av.watch.impress.co.jp/docs/news/20150106_682560.html [impress.co.jp]
VGA変換アダプタくらいは動作させられる位の給電はできるみたいですね
Re: (スコア:0)
その製品の電力の供給源は元コメの意図しているものとは方向が逆で、
HDMI入力側(ディスプレイなど)からではなく、HDMI出力側(ノートPCなど)から供給を受けて動作するものです。
(HDMIの仕様上、5Vのラインが存在しますが、これはHDMI出力からHDMI入力に向けて提供されるものです)
このトピックスの文脈から言うと、スティック型PC側が電力を吐き出す必要があります。
それをスティック型PC自身の電源に使うというのは、何がなんだか分かりません。
Re:そろそろHDMIから電力供給されないかなぁ (スコア:0)
HDMI 1.4から、ソース側に逆方向の電源供給できるようになってるよ。"5V/55mA以上"って曖昧な基準だけど。
x86 PCだと2Aは欲しいところ、しかも変動に耐えてくれる必要があるね。
Re: (スコア:0)
それは本当でしょうか?
私が不勉強なのかもしれませんが、HDMI1.4の仕様書にそんな記述あったようには思いません。
その"5V/55mA以上"というのはソース機器がシンク機器に向けて供給可能でなければならない基準で、
HDMI1.4からというわけではなく、もっと前から存在するものだと理解しています。
主張されている内容の情報源を示すことが可能であれば、教えて頂けないでしょうか?
(煽りではなく、ただ単純に私の理解が間違っているのであれば改めたいだけです)
Re:そろそろHDMIから電力供給されないかなぁ (スコア:1)
デバイスに対して最低限の電力(5V55mA)を供給するけど、デバイスの電力としてユーザに使わせるなよ。
http://www.hdmi.org/learningcenter/kb.aspx?c=13 [hdmi.org]
Re: (スコア:0)
その引用の中の一文、
にある通り、HDMI仕様は、全てのソース機器が5Vラインに少なくとも55mAを供給することを要求していて、
その目的は(デバイスを駆動するためのものではなくて)ディスプレイに組み込まれているEDID ROMを読みとるためのもの、
ということですよね。
シンク機器側(ディスプレイなど)からの電源供給については言及されていないと思います。
Re: (スコア:0)
HDMI1.4に含まれているかは知らないけど、MHL対応のHDMI入力端子なら最低500mA出力してくれるよ
http://www.toshiba.co.jp/tech/review/2012/01/67_01pdf/f03.pdf [toshiba.co.jp]
Re: (スコア:0)
情報提供はありがたいのですが、私がお聞きしているのはMHL規格ではなく、HDMI規格についてです。
それに最低500mAという点は、先に書かれている"5V/55mA以上"に合っていません。
Re: (スコア:0)
HPD は接続時にシンク側からソース側に5Vの電圧を送っていますね。
ソース側はそれで接続を確認します。電源供給というより信号にすぎませんが。
Re:そろそろHDMIから電力供給されないかなぁ (スコア:1)
そのとおりです。
そのHPDの5V信号は、製品によってはソース機器側が供給している5Vから作り出されています。
つまりシンク機器がソース機器側から供給された5VをHPDにリターンするだけ、という仕掛けです。
この方法はHPD信号の生成法の例としてHDMIの仕様書に紹介されています。
Re: (スコア:0)
http://av.watch.impress.co.jp/docs/news/20150107_682695.html [impress.co.jp]
次世代MHLで、HDMIポートから40W給電できるようになるみたいです。
Ultrabook程度のスペックを動かせそうですね。